Swing clamps, with upper flange and position control
Hydrokomp Hydraulische Komponenten GmbH Logo

Select your language

Inquiry list

Swing clamps, with upper flange (A), position control optionally

 

Swing clamp,
with upper flange,
position control optionally,
suitable for double clamping arms

 

Risk of injury:
If the swing clamp cylinder is under pressure considerable risks of injury by pinching or crushing are constantly present within the swing area during operation.
The safety instructions and the valid accident prevention regulations must be observed.

 

Description

Swing clamp cylinders release the clamping point on the workpiece. With this, it is easy to change the workpiece. This hydraulic swing clamp cylinder operates as single-acting or double-acting traction cylinder, whereas part of the stroke is used to rotate the piston. The model with 0° swing angle operates only vertical as traction cylinder. You can select between right or left turning versions with various standardized swing angles.

For oil supply, the cylinders are equipped with threaded port and manifold connection with O-ring for drilled channels. To guarantee a long lifetime the cylinders have an integrated metal wiper as standard. The swing clamp cylinder can be optionally supplied with a inductive or pneumatic position control. This feature controls the clamp and unclamp position of the cylinder. The position control is not included in the scope of supply of the standard cylinder.

For any risk of exceeding the permitted volume flow a throttle check valve must be interposed into the oil supply line.

The clamping motion is initiated by a superimposed swing and stroke motion. After that, a linear clamping stroke follows. Variants with 0°, 30°, 45°, 60° and 90° swing angles are available. The permitted operating pressure is depending from the clamping arm lenght. For retaining clamping arms, the piston rod is optionally available with different holders. You can select between pendulum and clevis. The pendulum allows to retain double clamping arms. With this feature it is possible eg. to clamp two workpieces at the same time or to create a support on one side during the clamping process.

These swing clamp cylinders are equipped with a reinforced swing mechanism. Thereby an overload protection is unnecessary. The reinforced swing mechanism compensates, for example the higher loads if double clamping arms should be used.

When using self designed double clamping arms it is recommended to insert a carrier with spring elements to guarantee the neutral position. During the mounting of the clamping arm, make sure that torques are transferred in the piston rod. Hold against the clamping arm when you tighten or loosen the fixing screw.

 

Special features:
  • protecting metal wiper

  • reinforced swing mechnism

  • inductive or pneumatic position control available

  • easy loading and unloading of the fixture

  • customer specific clamping arms can be mounted

  • standard and special clamping arms available

 

Design:


Type A, upper flange

The dimensioned installation contour can be found on the data sheet.

 

Clamping arm holders:


Clevis

Clamping arm:

  • SPG/h double clamping arm
 


Pendulum

Clamping arm:

  • SPP/g double clamping arm
 
 
Here you will find an overview of all standard clamping arms. Special clamping arms are available on request.
 

 

 

Hotline

We gladly consult you by phone call:

Customer service on-site

Find a consultant in your area!

Weltkarte mit HYDROKOMP Vertriebspartnerländern weltweit

Technology that connects

HYDROKOMP Headquarters 1

Founded 1998, HYDROKOMP designs, manufactures and distributes hydraulic components, coupling systems and clamping technology for mechanical engineering, fixture construction, tooling and many other branches of industry also for different operating conditions.

HYDROKOMP Headquarters 2

HYDROKOMP is the right supplier for companies of mechanical engineering fixture construction, tooling and many other branches of industry worldwide. Constructive ideas and customer-specific designs are our particular strengths.

HYDROKOMP Production Facility 1

Each and every one of our products is developed and manufactured according to the highest quality standards. With modern CAD systems we design new solutions. After that, current procedures of precision manufacture and quality assurance are next in process.

HYDROKOMP Production Facility 2

Our qualified employees and our modern CNC machinery ensure high flexibility product variety and quality. HYDROKOMP products are designed for long-lasting application in rough industrial daily routine. Our customers can surely trust that the process will flow smoothly.

previous arrow
next arrow

 

 

We use cookies on our website. Some of them are essential for the operation of the site, while others help us to improve this site and the user experience (tracking cookies). You can decide for yourself whether you want to allow cookies or not. Please note that if you reject them, you may not be able to use all the functionalities of the site.