Swing clamps, with flange and threaded body
Hydrokomp Hydraulische Komponenten GmbH Logo

Select your language

Inquiry list

Swing clamps, with lower flange (B) and threaded body (C)

 

Swing clamp,
with lower flange and threaded body, integrated overload protection

 

Risk of injury:
If the swing clamp cylinder is under pressure considerable risks of injury by pinching or crushing are constantly present within the swing area during operation.
The safety instructions and the valid accident prevention regulations must be observed.

 

Description

Swing clamp cylinders release the clamping point on the workpiece. With this, it is easy to change the workpiece. This hydraulic swing clamp cylinder operates as single-acting or double-acting traction cylinder, whereas part of the stroke is used to rotate the piston. The model with 0° swing angle operates only vertical as traction cylinder.

To guarantee a long lifetime the cylinders have an integrated metal wiper as standard. For oil supply, the cylinders are equipped with threaded port and manifold connection with O-ring for drilled channels. You can select between right or left turning models with various standardized swing angles. The integrated overload protection protects the swing mechanism from damage due blockage of the rotation or improper assembly of the clamping arm.

For any risk of exceeding the permitted volume flow a throttle check valve must be interposed into the oil supply line. Counter-hold the clamping arm when tightening or loosening the counter nut in order to prevent torque transfer to the piston rod and to avoid damage to the ball guide.

Variations with 0°, 30°, 45°, 60° and 90° swing angles are available. The permitted operating pressure is depending from the clamping arm length. Except from standard clamping arms also special clamping arms can be assembled. The maximum operating pressure of 500 bar does not apply for each clamping arm length. For details about the permitted operating pressure, see data sheet.

The swing clamp cylinders will be delivered ready for connection. If a modification of the threaded ports on manifold ports become necessary, proceed as follows:

single-acting and double-acting:
- insert G1/4 locking screws into the threaded port A
- remove the cap screws with seals out of the manifold connection port A
- insert the O-rings 7x1,5 into the countersink of the manifold connection port A

For the application of single-acting cylinders it is important to note, if the ventilation of the spring chamber should be realized by the manifold connection port you must replace the filter at port B with a G1/4 locking screw.

 

Special features:
  • protecting metal wiper

  • integraded overload protection

  • easy loading and unloading of the fixture

  • customer specific clamping arms can be mounted

  • standard and special clamping arms available

 

Designs:


Type B, lower flange

Type C, threaded body

 

Mounting dimensions can be found on the data sheet.

 
 

Clamping arm holder:


Taper, ratio 1:10

Clamping arms:

  • SPK/c single clamping arm
  • SPK/d single clamping arm
  • SPK/e single clamping arm
  • SPK/f  double clamping arm
 
Here you will find an overview of all standard clamping armsstandard clamping arms.
Special clamping arms are available on request.
 
 
 

 

 

Hotline

We gladly consult you by phone call:

Customer service on-site

Find a consultant in your area!

Weltkarte mit HYDROKOMP Vertriebspartnerländern weltweit

Technology that connects

HYDROKOMP Headquarters 1

Founded 1998, HYDROKOMP designs, manufactures and distributes hydraulic components, coupling systems and clamping technology for mechanical engineering, fixture construction, tooling and many other branches of industry also for different operating conditions.

HYDROKOMP Headquarters 2

HYDROKOMP is the right supplier for companies of mechanical engineering fixture construction, tooling and many other branches of industry worldwide. Constructive ideas and customer-specific designs are our particular strengths.

HYDROKOMP Production Facility 1

Each and every one of our products is developed and manufactured according to the highest quality standards. With modern CAD systems we design new solutions. After that, current procedures of precision manufacture and quality assurance are next in process.

HYDROKOMP Production Facility 2

Our qualified employees and our modern CNC machinery ensure high flexibility product variety and quality. HYDROKOMP products are designed for long-lasting application in rough industrial daily routine. Our customers can surely trust that the process will flow smoothly.

previous arrow
next arrow

 

 

We use cookies on our website. Some of them are essential for the operation of the site, while others help us to improve this site and the user experience (tracking cookies). You can decide for yourself whether you want to allow cookies or not. Please note that if you reject them, you may not be able to use all the functionalities of the site.